Ruger Forum banner

1 - 20 of 41 Posts

·
Registered
Joined
·
33 Posts
Discussion Starter #1
I just picked up pound of titegroup and was wondering who uses this and what you use it in. My intention is to use it in both 44 special and 45 auto.
 

·
Registered
Joined
·
1,806 Posts
I've never shot the 44 Special so can't help you there. I use Titegroup in 38 and 32 H&R. I have tried it in the 44 Mag and groups with me shooting were all over the place.
 

·
Registered
Joined
·
43 Posts
To me, slightly more "snappy" than unique (more of a push) @ same velocity out of short barrel .45 colt using 255gr .452 lead.
Accuracy was slightly better than unique loads within the 25yrds I tested.
 

·
Registered
Joined
·
128 Posts
Love it for 9mm
 

·
Registered
Joined
·
389 Posts
I use it in 9mm with loads using either...

Lee lead 124gr RN TL or Hornady 124gr RN match loads
 

·
Registered
Joined
·
256 Posts
I use it in reloading 38 Special, 357 Mag, 44 Mag & 500 Mag. I get excellent groups in all of these calipers. Just remember "A little goes a long way". Carefully measure your charges and follow reloading data.
 

·
Reloading Addict
Joined
·
10,714 Posts
I've used it 9mm, .40, .45acp and 45colt with good results in all of them.
 

·
Registered
Joined
·
1,262 Posts
I use TiteGroup regularly in .38 and .44 Special loadings. My favorite .44 load is a 200 gn LRNFP with 4.9 gns of TiteGroup. It's an accurate mouse fart load from my 7 1/2" Redhawk.
 

·
Registered
Joined
·
4 Posts
I load 5grs of Titegroup under a 200gr LRNFP bullet in .44 special.
Mild load that shoots well in both of my Ruger .44 Specials.
 

·
Registered
Joined
·
155 Posts
Since I can't find any 231, I use Titegroup in just about all my pistol calibers. Meters well, reasonably clean and shoot fine. What more can you ask?
 

·
Registered
Joined
·
396 Posts
I've never shot the 44 Special so can't help you there. I use Titegroup in 38 and 32 H&R. I have tried it in the 44 Mag and groups with me shooting were all over the place.
What load do you use in the 32 H&R?:confused:
 

·
Registered
Joined
·
308 Posts
I use it for cowboy and range loads for 38/357, 44 spl. 45 Colt, 41 long Colt and 45 AR. I use 5.0 grains for my 45 and 44 loads, My brother shoots the same load in 45 acp for competition.
 

·
Registered
Joined
·
68 Posts
I use it in 38spl,32 S&W Long,and 45acp. Burns clean and meters well in my Uniflow.
Only think to watch out for, it's such a low volume powder(takes up very little space) you could double or triple charge large volume cases(38,357,45 Colt,etc).
 

·
Registered
Joined
·
73 Posts
I use it for everything I load, mostly because it's what I can get locally. 9mm, 38 & 357, 45 ACP and 45 Colt (standard and R/O loads). Been happy with with it in all of those. It takes up very little volume in the cases so be careful as it is easy to "double charge" the load without it being very noticeable!

Steve
 
1 - 20 of 41 Posts
Top